Output from Netgear DGN2000 at startup



CFE version 1.0.37-12.1 for BCM96348 (32bit,SP,BE)
Build Date: "  6月 27 23:37:04 CST 2008 (root@Denis-Linux)
Copyright © 2000-2006 Broadcom Corporation.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
CPU type 0x29107: 240MHz, Bus: 133MHz, Ref: 26MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE:  0x80401000 - 0x80526130 (1200432)
Initialized Data:          0x8041D6E0 - 0x8041EE20 (5952)
BSS Area:                  0x8041EE20 - 0x80424130 (21264)
Local Heap:                0x80424130 - 0x80524130 (1048576)
Stack Area:                0x80524130 - 0x80526130 (8192)
Text (code) segment:       0x80401000 - 0x8041D6E0 (116448)
Boot area (physical):      0x00527000 - 0x00567000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.0.1:ffffff00  
Host IP address                   : 192.168.0.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-9)                    : 96348W3  
Number of MAC Addresses (1-32)    : 2  
Base MAC Address                  : 00:22:3f:55:7c:d6  
PSI Size (1-64) KBytes            : 24  
Serial Number (16) Chars          : 1WY191BX009FA  
PIN Code (8) Chars                : 39443007  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xbfc30000) ...
Code Address: 0x80010000, Entry Address: 0x801b4018
Decompression OK!
Entry at 0x801b4018
Closing network.
Starting program at 0x801b4018
Linux version 2.6.8.1 (root@BuildServer) (gcc version 3.4.2) #1 Mon Jun 14 13:48:56 CST 2010

Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB

96348W3 prom init

CPU revision is: 00029107

Determined physical RAM map:

 memory: 00fa0000 @ 00000000 (usable)

On node 0 totalpages: 4000

  DMA zone: 4000 pages, LIFO batch:1

  Normal zone: 0 pages, LIFO batch:1

  HighMem zone: 0 pages, LIFO batch:1

Built 1 zonelists

Kernel command line: root=31:0 ro noinitrd 

brcm mips: enabling icache and dcache...

Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.

Primary data cache 8kB 2-way, linesize 16 bytes.

PID hash table entries: 64 (order 6: 512 bytes)

Using 120.000 MHz high precision timer.

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 13696k/16000k available (1459k kernel code, 2284k reserved, 216k data, 84k init, 0k highmem)

Calibrating delay loop... 239.20 BogoMIPS

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Checking for 'wait' instruction...  unavailable.

NET: Registered protocol family 16

Total Flash size: 4096K with 71 sectors

File system address: 0xbfc30100

No flash for scratch pad!

Can't analyze prologue code at 8017b5b4

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

PPP generic driver version 2.4.2

NET: Registered protocol family 24

IMQ starting with 2 devices...

IMQ driver loaded successfully.

	Hooking IMQ before NAT on PREROUTING.

	Hooking IMQ after NAT on POSTROUTING.

Using noop io scheduler

bcm963xx_mtd driver v1.0

kernel_addr == 0xbff6b100 rootfs_addr == 0xbfc30100

Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank

 Amd/Fujitsu Extended Query Table at 0x0040

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

Creating 6 MTD partitions on "Physically mapped flash":

0x00030100-0x0036b100 : "fs"

mtd: partition "fs" doesn't start on an erase block boundary -- force read-only

0x00030000-0x00400000 : "tag+fs+kernel"

0x00000000-0x00010000 : "bootloader"

0x00020000-0x00030000 : "nvram"

0x00000000-0x00010000 : "bootloader"

0x00010000-0x00020000 : "DPF_file"

brcmboard: brcm_board_init entry

SES: LED GPIO 0x8022 is enabled

Serial: BCM63XX driver $Revision: 3.00 $

ttyS0 at MMIO 0fffe0300 (irq = 10) is a BCM63XX

Broadcom BCMPROCFS v1.0 initialized

NET: Registered protocol family 2

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 512 bind 1024)

ip_conntrack version 2.1 (125 buckets, 0 max) - 384 bytes per conntrack

ip_conntrack_h323: init 

ip_conntrack_pptp version 2.1 loaded

ip_conntrack_rtsp v0.01 loading

ip_nat_h323: initialize the module!

ip_nat_pptp version 2.0 loaded

ip_nat_rtsp v0.01 loading

ip_tables: © 2000-2002 Netfilter core team

NET: Registered protocol family 1

NET: Registered protocol family 17

NET: Registered protocol family 8

NET: Registered protocol family 20

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 84k freed


init started:  BusyBox v1.00 (2010.06.14-05:38+0000) multi-call binary

init started:  BusyBox v1.00 (2010.06.14-05:38+0000) multi-call binary

Starting pid 35, console /dev/tts/0: '/usr/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5

/usr/etc/rcS: 23: /usr/sbin/mybuf: not found
/usr/etc/rcS: 25: /usr/sbin/vpn_trigger: not found
bcm_enet: module license 'Proprietary' taints kernel.

Broadcom BCM6348B0 Ethernet Network Device v0.3 Jun 14 2010 13:47:28

Config Ethernet Switch Through MDIO Pseudo PHY Interface

ethsw: found bcm5325e!

dgasp: kerSysRegisterDyingGaspHandler: eth0 registered 

eth0: MAC Address: 00:22:3F:55:7C:D6

insmod: cannot open module `/lib/modules/vnet.ko': No such file or directory
blaadd: blaa_detect entry

adsl: adsl_init entry

netfilter PSD loaded - © astaro AG

ipt_random match loaded

device eth0 entered promiscuous mode

BcmAdsl_Initialize=0xC00733A8, g_pFnNotifyCallback=0xC008C2A4

AnnexCParam=0x7FFF7E68 AnnexAParam=0x00003987 adsl2=0x00000003

pSdramPHY=0xA0FFFFF8, 0x13DD5F 0xDEADBEEF

AdslCoreHwReset: AdslOemDataAddr = 0xA0FFA4D4

AnnexCParam=0x7FFF7E68 AnnexAParam=0x00003987 adsl2=0x00000003

dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 

ATM proc init !!!

RC: wifi_init()
/usr/sbin/wlctl: wl driver adapter not found
RC: insert wl.ko...
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)

wl: srom not detected, using main memory mapped srom info (wombo board)

wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000

wl0: MAC Address: 00:22:3F:55:7C:D6

wl0: Broadcom BCM4322 802.11 Wireless Controller 4.174.64.12.cpe1.1

dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 

ap_name=(null) action=start
br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

/bin/echo GMT+0 > /etc/TZ
killall: udhcpd: no process killed
killall: miniupnpd: no process killed
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
killall: dnrd: no process killed
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the
/etc/dnrd/master file or use -m off.
dnrd -a 192.168.0.1 -m hosts -c off --timeout=0 -b 
rc (wifi): wlChannel=11
Setting SSID "NETGEAR"
Setting SSID "NETGEAR2"
Setting SSID "NETGEAR3"
Setting SSID "NETGEAR4"
Setting country code using abbreviation: "ALL"
/usr/sbin/wlctl -i wl0 chanspec -c 11 -b 2 -w 20 -s 0
Chanspec set to 0x2b0b
rc: wps->unconfig
killall: wsccmd: no process killed
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.0.5, November 19 2006
*********************************************
Created @ Apr 16 2008 13:43:48
Initializing stack...button monitor start...!
 OK
Now starting stack
DEVICE PIN: 39443007
rc: start nas
route: SIOC[ADD|DEL]RT: File exists

Please press Enter to activate this console. 

Starting pid 413, console /dev/tts/0: '/bin/sh'


BusyBox v1.00 (2010.06.14-05:38+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# help

Built-in commands:
-------------------
	. : alias bg break cd chdir continue eval exec exit export false
	fg hash help jobs kill let local pwd read readonly return set
	shift times trap true type ulimit umask unalias unset wait

# 
#